An optional remote can be purchased for the PW600, PW900 and PW1800, P/No. PW REMOTE. To install the remote control, insert the plug into the data socket on the front panel. The remote has the ability to turn the inverter on and off remotely and indicate when the inverter is on.
UNDERSTANDING YOUR POWER REQUIREMENTS POWER REQUIREMENTS OF YOUR APPLIANCE/S:
All appliances have a rating plate that shows the amount of power (Watts) used or the current (Amps) drawn under normal use. The following table shows the maximum combined AC Watts or AC Amps which can be run by the inverter.
Some appliances that use an electric motor or transformer may draw up to 10 times their power rating when first turned on. These are called inductive loads and are the most difficult for the inverter to run. Contact your appliance manufacturer for further advice.
SUITABLE POWER SOURCE
In order to operate the inverter and supply power to an appliance a suitable 12V DC power supply is required, typically a vehicle or caravan battery, portable power pack or an independent 12V lead acid battery. For most applications, a deep cycle battery is recommended for best performance. The size of the battery used will determine how long the inverter will supply power to an appliance and how well the inverter will perform. Most batteries are marked with their size in Amp hours (Ah) or Cold Cranking Amps (CCA).
Because 12V inverters are capable of drawing high currents the inverter should only be connected to a suitable size battery. Connection to an undersized battery could damage the battery and will result in the inverter shutting down within a short period due to low battery voltage. The amount of power drawn from the battery is proportional to the inverter load.
Q. Why does the inverter turn itself off?
A. If the inverter’s audible alarm sounds and a fault L.E.D illuminates, this indicates that there is
a fault or error, and the inverter may turn off. Most commonly this would be caused by an
appliance that is drawing too much power (overloading), low battery voltage or voltage drop
due to insufficient size cables or poor connections (refer to ‘Understanding your Inverter’
tables, page 7).
Q. The Inverter will not run my appliance even though the appliance draws less power
(Watts) than the size of the inverter?
A. Electrical appliances can be divided into three groups by the way they draw energy (current)
from their power supply. These groups are “Resistive”, “Inductive” and “Capacitive” appliances
or also called “loads”. Some appliances may draw all three types of power.
such as normal incandescent lights (wire filament) always draw a constant
power (watts) from the power supply, that is a 100 Watt light will draw approximately
100 Watts from the power supply at all times. Resistive loads are the easiest appliances
for an inverter to run.
such as a refrigerator (Electric Motor) require a large rush of power (surge
current) to start and then usually draw a more constant power once running. Inductive loads
contain coils of wire (motors, transformers, ballasts, solenoids). When the power is first turned on,
these coils of wire draw a large surge current which forms the magnetic flux (magnetic field)
which allows these appliances to work. This magnetic flux is a kind of stored energy.
The most common inductive appliances are: fridges, air compressors, transformers/ chargers,
pumps, power tools and fluorescent lights. These appliances can draw up to 10 times their normal
running power to start up; that is to run a 80W fridge you may need a 600 or 1000 Watt inverter.
such as many TV’s or many electronic appliances require a large surge current
to start only when they have not been used for a while. This is often due to large capacitors in the
power supply that must be quickly charged when the appliance is turned on. If the appliance is not
used for a few days these capacitors slowly go flat. Resetting the inverter a couple of times may
allow these appliances to work.
There are some appliances such as large refrigerators, air conditioners and other pump driven
appliances that have extremely high start up currents, because they have an inductive motor
that must start under load. These appliances are not recommended for use with an inverter.
They should be powered by an engine driven generator.
Q. Why does it damage the inverter if the battery leads are reverse-connected?
A. Your inverter uses sophisticated electronics to convert DC battery power to AC mains power.
If you accidentally connect the inverter to the battery incorrectly (reverse polarity) a large current
will be drawn by the inverter which will blow the protection fuse. As this occurs some of the high
current could damage sensitive electronic components. Because of this risk it is important to
always double-check the battery polarity before making any connections.
Q. How do I check or change the fuses?
Pro-Wave inverters contain internal fuses and should only be checked or replaced by a qualified
electrical appliance repairer.
THE DC SUPPLY MUST BE DISCONNECTED BEFORE ANY REPAIR, THEN TURN THE ON/OFF
SWITCH OF THE INVERTER “ON” TO DISCHARGE THE CAPACITORS.
Q. Why does the fan only operate sometimes?
A. Pro-Wave inverters feature a temperature controlled automatic cooling fan that only operates
when needed. This allows the inverter to run very quietly for most of the time.
Q. Can I run laptop computers and other sensitive electrical appliances?
A. Yes. Pro-Wave’s pure sine wave output is suitable for medical equipment and sensitive electrical
appliances. They allow you to watch television without static, operate computers and gaming
consoles and run fluorescent lights.